Pages

Tuesday, August 18, 2009

It is good for me

I'm still in the process of comforting myself with choosing this rig setup:

"Any rig her owner likes to work is the best rig. John G Hanna"

Sailrite on cat rigs

This is quoted from the sailrite webpage ( www.sailrite.com )

"Cat Rig and Battens

Finally, consider the rig appropriate for these high-speed boats. You will have noticed that most high performance catamarans have a cat rig. This follows from our discussion of aspect ratios. The sloop rig tends to spread sail area out, in effect, decreasing aspect ratio. That sloop rig will make possible more power, but it will cut down the potential speed of the boat. If the boat is so easily driven that this power is not required in order to get it moving, it is best to place all sail area in a single, tall sail.

One more thing: high-speed sails should have full-length battens. These battens are tied into the sail with enough compressive force to bend them into the desired shape. As a result, the sail becomes so rigid that the sail must be "popped" from one side to the other when the boat is tacked. This rigidity holds the sail in shape in spite of rapid acceleration and deceleration and in spite of the abrupt apparent wind shifts, which accompany those changes in speed.

The rigidity imparted by the battens also lets the sail operate at higher angles of incidence than would otherwise be possible (see Marchaj's Sailing Theory and Practice, page 70). Once again, this can be very useful on a boat that moves the apparent wind well forward just because its own speed is so high. The power developed by such a sail will be relatively low, but its potential speed will be very high.

There are, in conclusion, no secrets in the building of high-speed sails. They are simply the result of extending the same lessons we have learned with "normal" sail design."

CE, CLP, SA

Currently having 33sqm of upwind SA. Mast is 12m long, needs to fit inside a container, it is also possible that it will be a collapsable 2 piece mast, however wouldn't want it longer. CE is aft of CLP by aproximately 6-7% of WL. Theoretically it should currently have a slight weather helm. I want a trackless mast, mainsail luff will be on a wire and will have a fairing sock around the mast, that is why the boom is not attached on the mast, don't want it to interfere with the wire. I think the main will be easier to reef if the luff is on a wire, less stuff to break or jam, less efficiency though, but hopefully the sock setup will work and draft from the mast will be reduced. I'm not looking for a maximum efficiency rig, just a simple one with less stuff to break or jam, easy to sail single handed, less hardware, cheaper. There will be some flying sails for downwind work.

Also modified mainbeam, simpler, still sufficient clearance under the beam, checked local suppliers and largest round Alu extrusion available is 100x4, so beams will have to be made from wood/carbon, probably won't need bow foil, will add gennaker setup soon.

Tuesday, August 11, 2009

HullShape 1108


Modified hull shape, symmetrical hull, asymmetrical deck, clearance between rear beam and designed WL is around 90cm, more than the Radical Bay 8000, but still a bit low. Hulls are fatter but WL beam is just 1cm more, WL to BWL is almost the same, almost 13. Next thing that came to my mind will be to further move the cockpit seat towards the trampoline, amplifying the aft berth space. Under sail the cockpits and entry hatch will be protected with a slick (hopefully) spray/sun hood.

Monday, August 10, 2009

ReadingDuty

As you can imagine I'm trying to get as much info and knowledge on designing cats, while reading stuff on the net the words of Ted Clements just brought a smile on my face.

"By design, a monohull sailboat almost invariably has to carry ballast well in excess of its ability to float it in the worse case. Ballast in itself is a useless lumpen cargo that strives to sink the boat from the moment it is launched. The decision to purchase it and float it around has to be counter-productive, if you have a choice. The nice thing about sailing catamarans is that they manage to stay upright by cheating, (all form stability, no ballast) so; you do have a choice."

Clearly the world is split into smokers and non smokers, cyclists and drivers, catsailors and monosailors etc...

EvolutionProcess

I'm currently thinking of a redesign. I've been pondering a lot these days on the actual build process. This cat must be practical within my budget, not just nice. Currently I'm debating wether it is efficient having asymmetrical hulls, especially when I'm considering building the hulls in female moulds. That would mean 2 female moulds, which is not good. I would go with a redesign - new symmetrical hulls, keeping the B/WL ratio, but with asymmetrical decks. Why female moulds ? Sanding the outside of a 9m cat is not an easy and fast process, quite the oposite. Female mould will save considerable time from the build process, also that will imply foam. This is probably one of the many turning points of the project, untill a satisfactory solution will come up. Foam will be 3 times more expensive than a wood core, most probably.

Sunday, August 9, 2009

HomeDelivery


Did I mention I want it to fit in a standard 40' container ?
Just in case...